SpeedFan 4.44 introduced a new and improved fan control strategy. Let us first recall some concepts and definitions:

• any computer can have any number of fans, from 0 up.
• On a specific computer, SpeedFan might be able to read fan speed RPMs (Revolutions Per Minute). SpeedFan might not be able to read the RPMs of all installed fans. If SpeedFan can read no RPM, check for future SpeedFan releases as hardware support improves over time.
• On a specific computer, SpeedFan might be able to access SPEED controls (usually referred to as PWMs). If you would like to know more about PWM, feel free to read this article. Please note that RPM readings and PWM settings are not necessarily tied together. The hardware monitor chips located inside computers have some wires to read fan speeds and some others to control PWMs. It is up to the computer manufacturer to decide whether and how to connect those wires. Understanding which SPEED (PWM) acts (controls) which fan can be a matter of trial and error, but it is worth the effort.
• Every fan reacts to PWM control differently. 4-wire fans usually exhibit a rather linear response. 3-wire fans can be much less linear. It depends on several factors, including the circuitry on the motherboard and the type of fan used.

That said, let's move on and have a look at the basic concepts behind SpeedFan's Advanced Fan Controllers. A Fan Controller links a specific PWM control (the Controlled Speed) to the current value of any number of source temperatures. For each temperature we can define the response curve. This means that we can define what PWM value we want to apply for every temperature value. Each temperature can have a different response. Let's see how to create our own first Fan Controller. Start SpeedFan, press CONFIGURE button and select the Fan Control tab. Enlarge the window if needed. In the example image we have already created a Fan Controller and called it "CPU Fan Control Strategy". We can create more using the Add button on the right. With the Remove button we can delete a fan controller we previously created. As soon as we select "CPU Fan Control Strategy" in the list box, its parameters will appear below in the window. A Fan Controller requires a PWM to act on. Multiple temperatures can be used to control the PWM. For each temperature is defined its response curve. The final value applied to the controlled PWM depends on the selected method: either MAX of speeds or SUM of speeds. When a temperature is selected in the list box, the relevant configuration parameters appear on the left side. The response curve determines the requested PWM value (ranging from 0% to 100%) depending on the current temperature. By using the "<" and ">" buttons, the minimum and the maximum temperature levels can be selected. If the current temperature is below the minimum, the selected PWM value will be the one assigned to the minimum temperature. If the current temperature is higher than the maximum, the selected PWM value will be the one assigned to the maximum temperature. The hysteresis value is used to avoid fan fluctuations. In a few words, when the temperature rises, the new PWM value is applied immediately. When it lowers, the last applied PWM value is kept until the current temperature is hysteresis degrees lower than the temperature that caused the current PWM to be applied.

The SPEEDS tab allows to set some parameters for each PWM control. The Advanced Fan Control strategy keeps into consideration the "Minimum value" and the "Maximum value" set in this tab. This means that if the computations based on the temperature response curves lead to, say, a PWM value of 30%, but the SPEEDS tab defines 45% as the minimum value for that PWM, 45% will be used instead. These settings are shared with the standard fan control method.

The TEMPERATURES tab allows to define a warning level for each temperature. This warning level is taken into consideration by the Advanced Fan Control strategy: if a temperature exceeds its warning level, SpeedFan will forcibly set the relevant PWM to 100%.

Activating the Automatic Fan Speed checkbox on the main screen enables fan control. Whether the old fan control or the new Advanced Fan Control strategy is used depends on the Advanced Fan Control checkbox on the FAN CONTROL tab of the CONFIGURE window. If it is not set, the old fan control style is used.

This feature is a long awaited one. I speeded up development and release to the public. Suggestions are welcome.

Web

www.almico.com

Page generated in 0.0559 seconds

Powered by (new)...

Page viewed 2328490 times

-

Did you know that SpeedFan has an feed?

Privacy policy